Error Handler

Camel supports pluggable ErrorHandler strategies to deal with errors processing an Event Driven Consumer.

An alternative is to specify the error handling directly in the DSL using the Exception Clause.

Exception Clause

Using Error Handler combined with Exception Clause is a very powerful combination. We encourage end-users to use this combination in your error handling strategies. See samples and Exception Clause.

Using try …​ catch …​ finally

Related to error handling is the Try Catch Finally as DSL you can use directly in your route. Its basically a mimic of the regular try catch finally in the Java language but with more power.

The current implementations Camel provides out of the box are:

Non transacted

  • DefaultErrorHandler is the default error handler in Camel. This error handler does not support a dead letter queue, it will propagate exceptions back to the caller, as if there were no error handler at all. It has a limited set of features.

  • Dead Letter Channel which supports attempting to redeliver the message exchange a number of times before sending it to a dead letter endpoint

  • NoErrorHandler for no error handling

Transacted

  • TransactionErrorHandler is the default error handler in Camel for transacted routes. See the Transactional Client EIP pattern.

These error handlers can be applied in the DSL to an entire set of rules or a specific routing rule as we show in the next examples. Error handling rules are inherited on each routing rule within a single RouteBuilder

Short Summary of the provided Error Handlers

DefaultErrorHandler

The DefaultErrorHandler is the default error handler in Camel. Unlike Dead Letter Channel it does not have any dead letter queue, and do not handle exceptions by default.

Dead Letter Channel

The Dead Letter Channel will redeliver at most 6 times using 1 second delay, and if the exchange failed it will be logged at ERROR level.

You can configure the default dead letter endpoint to use: or in XML DSL:

<camel:errorHandler id="deadLetterErrorHandler" type="DeadLetterChannel" deadLetterUri="log:dead">

<camel:camelContext errorHandlerRef="deadLetterErrorHandler">
  ...
</camel:camelContext>

No Error Handler

The no error handler is to be used for disabling error handling.

errorHandler(noErrorHandler());

or in XML DSL:

<camel:errorHandler id="noErrorHandler" type="NoErrorHandler"/>

<camel:camelContext errorHandlerRef="noErrorHandler">
  ...
</camel:camelContext>

TransactionErrorHandler

The TransactionErrorHandler is the default error handler in Camel for transacted routes.

TIP:If you have marked a route as transacted using the transacted DSL then Camel will automatically use a TransactionErrorHandler. It will try to lookup the global/per route configured error handler and use it if it is a TransactionErrorHandlerBuilder instance. If not Camel will automatically create a temporary TransactionErrorHandler that overrules the default error handler. This is convention over configuration.

Features support by various Error Handlers

Here is a breakdown of which features are supported by the Error Handler(s):

Feature Supported by the following Error Handler

all scopes

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

onException

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

onWhen

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

continued

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

handled

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

Custom ExceptionPolicy

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

useOriginalBody

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

retryWhile

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

onRedelivery

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

RedeliveryPolicy

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

asyncDelayedRedelivery

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

redeliverWhileStopping

DefaultErrorHandler, TransactionErrorHandler, Dead Letter Channel

dead letter queue

Dead Letter Channel

onPrepareFailure

DefaultErrorHandler, Dead Letter Channel

See Exception Clause documentation for additional documentation of the features above.

Scopes

The error handler is scoped as either:

  • CamelContext - Globally in XML or globally only within the same RouteBuilder in Java DSL

  • Route - Individually per route

The following example shows how you can register a global error handler for the RouteBuilder:

RouteBuilder builder = new RouteBuilder() {
    public void configure() {
        errorHandler(deadLetterChannel("seda:error"));

        // here is our regular route
        from("seda:a").to("seda:b");
    }
};

The following example shows how you can register a route specific error handler

RouteBuilder builder = new RouteBuilder() {
    public void configure() {
        // this route is using a nested error handler
        from("seda:a")
            // here we configure the error handler
            .errorHandler(deadLetterChannel("seda:error"))
            // and we continue with the routing here
            .to("seda:b");

        // this route will use the default error handler
        from("seda:b").to("seda:c");
    }
};

Spring based configuration

Java DSL vs. Spring DSL The error handler is configured a bit differently in Java DSL and Spring DSL. Spring DSL relies more on standard Spring bean configuration whereas Java DSL uses fluent builders.

The error handler can be configured as a spring bean and scoped in:

  • global (the <camelContext> tag)

  • per route (the <route> tag)

  • or per policy (the <policy>/<transacted> tag)

The error handler is configured with the errorHandlerRef attribute.

Error Handler Hierarchy
The error handlers is inherited, so if you only have set a global error handler then its use everywhere. But you can override this in a route and use another error handler.

Spring based configuration sample

In this sample we configure a Dead Letter Channel on the route that should redeliver at most 3 times and use a little delay before retrying. First we configure the reference to myDeadLetterErrorHandler using the errorHandlerRef attribute on the route tag.

    <camelContext xmlns="http://camel.apache.org/schema/spring">
        <template id="myTemplate"/>
		<!-- set the errorHandlerRef to our DeadLetterChannel, this applies for this route only -->
        <route errorHandlerRef="myDeadLetterErrorHandler">
            <from uri="direct:in"/>
            <process ref="myFailureProcessor"/>
            <to uri="mock:result"/>
        </route>
    </camelContext>

Then we configure myDeadLetterErrorHandler that is our Dead Letter Channel. This configuration is standard Spring using the bean element. And finally we have another spring bean for the redelivery policy where we can configure the options for how many times to redeliver, delays etc.

    <!-- here we configure our DeadLetterChannel -->
	<bean id="myDeadLetterErrorHandler" class="org.apache.camel.builder.DeadLetterChannelBuilder">
	    <!-- exchanges is routed to mock:dead in cased redelivery failed -->
        <property name="deadLetterUri" value="mock:dead"/>
		<!-- reference the redelivery policy to use -->
        <property name="redeliveryPolicy" ref="myRedeliveryPolicyConfig"/>
    </bean>

    <!-- here we set the redelivery settings -->
	<bean id="myRedeliveryPolicyConfig" class="org.apache.camel.processor.errorhandler.RedeliveryPolicy">
	    <!-- try redelivery at most 3 times, after that the exchange is dead and its routed to the mock:dead endpoint -->
        <property name="maximumRedeliveries" value="3"/>
		<!-- delay 250ms before redelivery -->
        <property name="redeliveryDelay" value="250"/>
    </bean>

Using the transactional error handler

The transactional error handler is based on spring transaction. This requires the usage of the camel-spring or camel-jta component.

See Transactional Client that has many samples for how to use and transactional behavior and configuration with this error handler.

Back to top